{
 "schema": "otterchip.model_e.release_status/1",
 "generated": "2026-11-06T05:25:46.902747+00:00",
 "revision": "E-mech-r1",
 "parameters_source": "FROZEN by root 2026-11-06 for reference geometry: optimization/provisional-selected.json and results.json frozenParams (height 245, tilt 18, setback 180, rear 92, deck 62.5, drop 23, slope 0). Remaining keys are the Model E defaults in web/otterchip-model-e.js.",
 "print_prototype_release": {
  "state": "RELEASED FOR COUPONS AND GATED PROTOTYPE PRINTING",
  "stage_A": "Coupons, drill template and shims may be ordered now.",
  "stage_B": "Shell and parts only after gates G0-G5 and G9 close with measurements."
 },
 "production_approval": {
  "state": "NOT APPROVED",
  "reason": "Needs a physical prototype, measured donors, child-product safety review, electrical/thermal review and supplier DFM. See gate G10."
 },
 "excluded": [
  "rear cover dock (viewer study only; not in this CAD or BOM)",
  "seat lid and any sitting provision"
 ],
 "not_verified": [
  "measured donor fit",
  "child sit/lean load",
  "electrical safety",
  "thermal safety",
  "acoustic performance",
  "tip stability",
  "FEA of any kind (none was run)"
 ],
 "automated_checks": {
  "printed_parts": 58,
  "brep_valid": true,
  "single_solid": true,
  "watertight": true,
  "step_roundtrip": true,
  "max_mesh_volume_error": 0.00701,
  "interferences": 0,
  "fastener_checks": 87,
  "fastener_failures": 0,
  "service_paths": {
   "1 palm cover (carrier + pad) straight up": true,
   "2 instrument-deck wings straight up": true,
   "3 wheel cradles with wheels straight up": true,
   "4 keybed + backing bed + rear strip unit: lift 3, forward 42, then up": true,
   "5 typing bed slides forward under the lip, then up (music bay emptied)": true,
   "service panel drops": true,
   "Pi bracket + stack drops through the service opening (panel removed; rear power plate removed)": true,
   "left port plate + jacks withdraw inward": true,
   "right port plate withdraws inward": true
  },
  "stack": {
   "status": "Geometry-only checks on photo-derived donor estimates. Physical donor fit is NOT verified.",
   "deck": 62.5,
   "drop": 23,
   "slope_deg": 0,
   "key_top_typing": 73.3,
   "black_top_center": 39.5,
   "white_top_front": 31.0,
   "gap_typing_bed_to_black_top": 6.4,
   "gap_if_black_top_is_upper_estimate_32": 3.4,
   "keybed_underside_Z": 10.5,
   "floor_top": 5.2,
   "under_keybed_available": 5.3,
   "backing_bed": 3.0,
   "shim_room": 2.3,
   "wheel_bottom_Z": 12.0,
   "wheel_to_floor": 6.8,
   "deck_physical_stack_floor": 61.2,
   "deck_margin_over_physical_floor": 1.3,
   "bridge_front_viewer_z": 88.35,
   "black_key_outer_front_viewer_z": 116.9,
   "black_key_flat_top_front_viewer_z": 113.4,
   "black_key_outer_envelope_ahead_of_cad_bridge": 28.55,
   "black_key_flat_top_ahead_of_cad_bridge": 25.05,
   "black_key_flat_top_ahead_of_viewer_keyboard_edge": 26.1,
   "black_key_metric_note": "Local z 19.1 is the outer key envelope/ramp; local z 15.6 is the flat top used by the solver. The flat-top value ahead of the CAD lip is the ergonomic gate number. Estimates from photos.",
   "bridge_face_vs_viewer_note": "CAD bridge face includes the 3.2 mm lip wall at viewer z 88.35; the viewer keyboardFrontZ is 87.30, so CAD black-key top exposure is about 1 mm shorter than optimization blackKeyExposureMm.",
   "bridge_note": "Fingers cannot pass under the typing bridge (gap above is smaller than a fingertip). Usable black-key contact ends at the bridge front face.",
   "pass": true
  },
  "wall_probe": {
   "values": {
    "floor front module": 3.2,
    "side wall rear_lower z=-150": 3.2,
    "rear wall rear_lower x=0 y=30": 3.2,
    "side wall head": 3.2
   },
   "nominal": 3.2,
   "ok": true
  },
  "envelope": {
   "width": 355.0,
   "depth": 415.42,
   "top_Z": 338.01,
   "bottom_Z": 2.0,
   "expected": {
    "width": 355,
    "depth": 415.42,
    "top_Z": 338.01,
    "bottom_Z": 2.0
   },
   "ok": true
  },
  "model_m_tree": "clean"
 }
}