{
 "schema": "otterchip.model_e.mechanical.fit-gates/1",
 "generated": "2026-11-06T05:24:53.202847+00:00",
 "rule": "Order the Stage B shell only after G0-G5 are closed with measured values entered into parameters.json and build.py + docs.py re-run. CAD validity/mesh QA/interference QA are not donor fit, acoustic, thermal, tip or load verification.",
 "gates": [
  {
   "id": "G0",
   "title": "Process coupons (rigid PA12, flexible TPU, cheap FDM template)",
   "items": [
    "Rigid PA12 (same bureau/material as the shell): insert ladder (M3 3.8-4.2, M4 5.5-5.9 incl. poster 5.7, M2.5 3.8-4.2 incl. poster 4.0), tolerance ladder, bearing/shaft ladder (MR84 7.90-8.00, 625ZZ 15.90-16.00, 4.0-5.05 shafts), DC-inlet cutout, display/typing/bay/carrier/grille sections, keybed gauge, floor land + donor window, left side jack window.",
    "Flexible TPU is process-gated and has no blanket approval: test the pad segment in the process you intend to use. Powder 88A needs supplier acceptance of the actual wall thickness. FDM 95A is a separate option and needs its own wall and comfort check; the pad skin is 1.8 mm in CAD.",
    "Cheap FDM: side-profile template (PLA/PETG).",
    "TPU parts (pad, tyre, mic boots) are confirmed separately. Candidate: Xometry MJF TPU 88A BASF Ultrasint TPU01 dyed black; boot lip 1.2 mm against the 1.016 mm vendor guidance. Verify boot squeeze/capsule retention and tyre grip on printed parts."
   ],
   "status": "OPEN"
  },
  {
   "id": "G1",
   "title": "HARD GATE - display (dual official sources)",
   "items": [
    "Manufacturer dimension image: 245.19 x 162.77 x 11.6 (2021-12-21). Manufacturer STEP: 248.39 x 165.97 x 11.50 rim, front planar face 245.39 x 162.97 (header 2024-08-26; reference/waveshare-step-inspection.json). Glass-vs-rim interpretation is plausible but NOT documented; no revision is asserted.",
    "CAD choice: ADAPTABLE pocket for the larger STEP rim (249.59 x 167.17 incl. 0.6/side) + removable 1.6 mm/side display_spacer_frame for a drawing-size unit. Grille inserts follow the pocket height (167.17).",
    "Measure the purchased unit (W/H at 3 places, T, corner radius, port edge and port positions, button, VESA thread/depth). Then: use/omit the spacer frame, or edit display.envelope / pocket_clearance_per_side / face_recess / gasket_thickness / grille.half_height / port_side_after_install and rebuild.",
    "Test on cpn_display_corner_seat and the acoustic head section before printing shell_head."
   ],
   "status": "OPEN - blocks shell_head"
  },
  {
   "id": "G2",
   "title": "Typing kit (GK64X)",
   "items": [
    "PCB outline/holes vs GH60 nominal (bed pilots only), plate thickness/height, DSA cap height, stabilisers, USB-C plug (notch x -134..-114).",
    "Fit the 317 x 94 x 3 bed under the 14.1 mm side lips on cpn_typing_well_corner."
   ],
   "status": "OPEN"
  },
  {
   "id": "G3",
   "title": "LPK25 mk2 opened donor",
   "items": [
    "Frame W x D (CAD 293 x 99 est.), key top heights (29/20.5), front travel (8) and tail rise (1.2); 5 mm finger reserve check on cpn_keybed_profile_gauge.",
    "Black-top height: inferred 29 (range 26-32). Model E gap to the typing bed is 6.4 mm nominal, 3.4 mm at 32. Adjust with fork shims.",
    "F14 screw length follows the shim stack (build-guide table): at least 2 mm engagement and at least 0.3 mm tip recess. Measure the real stack; no protruding screw is allowed.",
    "Factory screw positions/thread/head height -> drill the MC13 backing bed from the opened donor, confirm heads fit the floor windows (+/-4 mm photo tolerance reserved); ribbon exit/length; controller PCB on the tray.",
    "Bridge: flat black-key top ahead of the CAD typing lip is 25.05 mm nominal (outer key envelope 28.55 mm; viewer keyboard edge gives 26.10 mm). A hand test on cpn_keybed_profile_gauge plus a mock bridge is required; numerical clearance is not a hand test.",
    "Instrument deck parts 2 mm vs key tails (~1.3 mm nominal)."
   ],
   "status": "OPEN"
  },
  {
   "id": "G4",
   "title": "Wheels and volume mechanism",
   "items": [
    "Mod wheels: MR84ZZ press fit (ladder), 3382H-1 rotor on the 2.90 D-flat (rotor bore 4.0 +0.102/-0.051: min 3.949 may bind on a 4.00 h6 shaft - lap the end if needed), endfloat with 0.4 shims, stop travel, sensor carries no radial load.",
    "Volume: 625ZZ press fit, 5 mm shaft + flat, Ruland FCMR16-6-5-SS alignment (10 mm engagement each side, max 12.3) and its 20.22 screw clearance, EM14R0D-M25 bushing nut under the plate, TPU01 tyre grip/creep on the 46.0 core (0.88 % stretch)."
   ],
   "status": "OPEN"
  },
  {
   "id": "G5",
   "title": "Acoustic prototype: right side first, then BOTH sides before the full body",
   "items": [
    "Left and right plenums are asymmetric (left is the display-port side: deeper baffle, narrower join). Test the right-side subset first, then build and test the matching left subset (mirror section + chamber/baffle/grille L) before ordering the full shell.",
    "Print the A_acoustic_prototype set: acoustic_head_section_R + speaker_chamber_R + speaker_baffle_R (with closed plenum) + grille_insert_R + acoustic_display_mock_R (or the real monitor); gasket_chamber_R + gasket_plenum_R from EPDM.",
    "Chamber rim gaskets are one closed piece per side, cut from the rear-box sealing face (see gasket_chamber_L/R STEP and qa.json gasket_rim_qa). Leak-test them; CAD contact is not a seal test.",
    "Pressure path: cone -> plenum cup -> join -> outlet duct -> own grille insert (front band + side wrap); rear wave sealed in the chamber. Close the section cut faces with a baffle board/tape.",
    "Tests: on-axis/30 deg frequency response vs a bare-driver reference; insertion loss with/without the grille insert; leak check (low-frequency sine at rated power + smoke/tissue around gaskets, or pressure-hold); rattle/buzz sweep 50 Hz-10 kHz; cone motion at max excursion (no contact, visual/feeler); later with both sides: stereo separation and L/R match.",
    "CAD: right net 584 cm3, left net 584 cm3 (gross - 50 cm3 assumed driver displacement); no acoustic performance claimed."
   ],
   "status": "OPEN"
  },
  {
   "id": "G6",
   "title": "Audio/electronics modules (frozen audio set)",
   "items": [
    "Pi 4B 4GB + HiFiBerry on pi_bracket (58 x 49, 8 mm standoffs) - unplug the external power adapter; disconnect the power-entry harness and remove the rear power-entry plate assembly first; unplug J4/J5/HDMI/USB; remove the service panel (7 screws; PUI and HB1 carriers come with it); remove the 4 lower bracket screws (Z 120/129); drop the bracket + Pi stack straight down through the 250 x 205 opening, rear edge Y 245.3 versus bracket back Y 241.9. The solid sweep is checked in qa.json service_paths..",
    "PUI AMP2X15 on pui_amp_carrier (66.0 x 40.6, 4 mm standoffs; plug exits +x/+Y 25 mm kept clear). HB1 (SparkFun PRT-13268) on hb1_carrier; MIKROE-5721 + D24V10F3 above it on nylon spacers. Tensility 54-00152 on rear_a (cutout chosen with cpn_dc_inlet_cutout).",
    "Harness: K1 COM -> HAT J4 and all head harness lengths must be re-measured on the Model E placement: Pi is at dY 30.9, dZ 18.9 from the frozen audio arrangement and jacks moved to the left wall. Shielded twisted pair for K1; audio B-MIC-5 / B-GND-1 remain open..",
    "MC12 headphone carrier: drill post holes to the Adafruit 4685 standoff sample; fit 2x 150 mm ties over the CN1/CN2 housings (loop ~= 2 x (28.4 mm slot spacing + 20.7 mm plate-bottom-to-module-top) = 98.2 mm before head/ratchet/tail allowance -> 150 mm ties); do a sample pull/retention check (board must not lift at the rear or slide under gentle plug insertion/removal) before closing the panel.",
    "Mic: roof ports x +/-40 (\u00d87, 1.2 thin zone), TPU 88A boots (1.2 mm lip) with \u00d89 mesh and 1.2 mm capsule-face gap (audio B-AC-1 re-check), \u00d816 x 25 lead envelopes. Measured CAD distances boot->chamber/baffle L 87.1 / 86.2 / R 102.5 / 84.9 mm (below the earlier 60 mm wish; accepted prototype deviation - mic isolation is decided by audio B-AC-2; B-AC-1 covers port response).",
    "Driver service: drivers are rear-mounted behind closed plenums - grille removal alone does NOT release a driver. Order: remove head (12 S2 bolts), chamber screws from inside, lift chamber+baffle, then 4 driver screws.",
    "Audio requested a rear hatch: not implemented; bottom service opening is the access path.",
    "Thermal: no thermal analysis exists; Model E keeps the rear vents but the head geometry changed. Measure under load.",
    "Electrical safety: not reviewed by this mechanical package."
   ],
   "status": "OPEN"
  },
  {
   "id": "G9",
   "title": "Model E side ports (new, not validated)",
   "items": [
    "Left wall: 6.35 mm NMJ6 + 3.5 mm SJ-435 at viewer z -70.0 / -90.0, y 30.0. Right wall: C&K 7000 rocker at z -80.0, y 30.0.",
    "Test real jacks, straight and right-angle plugs, wiring bend radius and rocker terminals on cpn_side_jack_window and the port plates before ordering shell_rear_lower.",
    "Decide with users: side cable exit on a table, plug strike risk, and child reach to the power rocker."
   ],
   "status": "OPEN"
  },
  {
   "id": "G7",
   "title": "Bureau preflight",
   "items": [
    "Per-part STL; bureau fit by axis permutation only: shell_front [355.0, 175.8, 60.73] fits ['universal_split_target', 'JLC3DP_MJF_PA12', 'JLC3DP_SLS_3201PA', 'Protolabs_MJF', 'Xometry_MJF_recommended', 'PCBWay_SLS', 'Sculpteo_PA12_raw']; shell_rear_lower [355.0, 239.62, 134.9] fits ['universal_split_target', 'JLC3DP_MJF_PA12', 'JLC3DP_SLS_3201PA', 'Protolabs_MJF', 'Xometry_MJF_recommended', 'PCBWay_SLS', 'Sculpteo_PA12_raw']; shell_head [355.0, 150.26, 201.11] fits ['universal_split_target', 'JLC3DP_MJF_PA12', 'JLC3DP_SLS_3201PA', 'Protolabs_MJF', 'Xometry_MJF_recommended', 'PCBWay_SLS', 'Sculpteo_PA12_raw']. One-piece shell NOT selected.",
    "Confirm warp risk, tolerance class and insert installation."
   ],
   "status": "OPEN"
  },
  {
   "id": "G10",
   "title": "Production approval (not granted by this package)",
   "items": [
    "Requires: physical prototype, measured donors, child-product safety review (small parts, sharp edges, pinch, tip, cords), electrical/thermal safety review, material and cleaning review, supplier DFM. None have been done."
   ],
   "status": "OPEN - NOT APPROVED FOR PRODUCTION"
  },
  {
   "id": "G8",
   "title": "Structure / child load - NOT RATED",
   "items": [
    "No load rating exists and no child sit/stand/lean load is claimed. Model E has no seat lid. The carrier crossbar is not a seat beam.",
    "Tip stability is untested. Model E is taller and deeper than Model M with a lower deck: weigh and tip-test; ballast is OPTIONAL until that test.",
    "Never load the display, keys, grille inserts, roller or TPU pad."
   ],
   "status": "OPEN - no rating claimed"
  }
 ]
}