Otterchip Model E (355 mm, LPK25, side ports) - mechanical build guide

Revision E-mech-r1, 2026-11-06T05:24:53.202847+00:00. Adapted from the Model M build by the Model E mechanical worker (claude-opus-5-5, high). Selection status: FROZEN by root 2026-11-06 for reference geometry: optimization/provisional-selected.json and results.json frozenParams (height 245, tilt 18, setback 180, rear 92, deck 62.5, drop 23, slope 0). Remaining keys are the Model E defaults in web/otterchip-model-e.js.

Release status: prototype print release only. NOT approved for production. Do not order the large shell until gates G0-G5 and G9 close with measured values and the CAD is rebuilt. Coupons come first.

Reading the print files

Each STL holds one part geometry; quantity is not multiplied inside the file. Stage 3MF bundles hold one object per part and can mix PA12, TPU and conditional parts, so they are inspection collections, not print jobs. Duplicate meshes or set quantities from print-schedule.csv (for example, 6 of each shim). Flexible parts are process-gated by G0, with no blanket 88A approval.

Backing-bed screw length (F14)

Floor 3.2 mm + land 1.3 mm = 4.5 mm before the shim; the bed is 3 mm. Each screw needs at least 2 mm thread engagement and at least 0.3 mm tip recess below the top of the bed. That gives a length of 6.5 to 7.2 mm plus the shim thickness. Measure the real stack: it overrides this table, and no protruding screw is allowed.

shimallowed lengthuseengagementtip recess
0.57.0 to 7.7trim an 8 mm screw to 7.52.50.5
1.07.5 to 8.28 mm screw as supplied (nominal)2.50.5
2.08.5 to 9.2trim a 10 mm screw to 92.50.5

Purchased-part references

Sourcing and audio snapshots with hashes: component references (published site). In the engineering package or repository, use ../../../manufacturing/component-references/index.html from this file. Manufacturer CAD used as references is in mechanical/src/ref_models/.

Selected first-build printed parts

partqtymaterialstageprint extents
shell_front1rigid PA12 (MJF/SLS)B_prototype_shell355.0x175.8x60.73
shell_rear_lower1rigid PA12 (MJF/SLS)B_prototype_shell355.0x239.62x134.9
shell_head1rigid PA12 (MJF/SLS)B_prototype_shell355.0x150.26x201.11
cushion_carrier1rigid PA12 (MJF/SLS)B_prototype_parts355.0x62.45x53.5
wrist_pad_tpu1flexible TPUB_prototype_parts303.6x44.6x14.6
instrument_deck_rear1rigid PA12 (MJF/SLS)B_prototype_parts338.4x40.35x25.0
instrument_deck_wing_L1rigid PA12 (MJF/SLS)B_prototype_parts22.1x63.6x2.0
instrument_deck_wing_R1rigid PA12 (MJF/SLS)B_prototype_parts22.1x63.6x2.0
bed_drill_template1cheap FDM (PLA/PETG)A_fit_and_beds293.0x96.9x2.0
shim_1p0mm6rigid PA12 (MJF/SLS)A_fit_and_beds18.0x18.0x1.0
shim_2p0mm6rigid PA12 (MJF/SLS)A_fit_and_beds18.0x18.0x2.0
wheel_cradle_L1rigid PA12 (MJF/SLS)B_prototype_parts19.0x41.5x24.3
wheel_cradle_R1rigid PA12 (MJF/SLS)B_prototype_parts19.0x41.5x24.3
controller_tray1rigid PA12 (MJF/SLS)B_prototype_parts40.0x80.0x12.8
display_carrier1rigid PA12 (MJF/SLS)B_prototype_parts110.0x168.0x10.5
display_spacer_frame1rigid PA12 (MJF/SLS)B_prototype_parts249.29x12.55x166.87
speaker_chamber_L1rigid PA12 (MJF/SLS)B_prototype_parts85.0x130.0x87.05
speaker_baffle_L1rigid PA12 (MJF/SLS)B_prototype_parts85.0x182.09x41.8
grille_insert_L1rigid PA12 (MJF/SLS)B_prototype_parts36.8x18.8x166.77
speaker_chamber_R1rigid PA12 (MJF/SLS)B_prototype_parts85.0x110.0x101.05
speaker_baffle_R1rigid PA12 (MJF/SLS)B_prototype_parts85.0x182.09x27.8
grille_insert_R1rigid PA12 (MJF/SLS)B_prototype_parts36.8x18.8x166.77
port_plate_side_left1rigid PA12 (MJF/SLS)B_prototype_parts13.2x67.0x21.5
port_plate_side_right1rigid PA12 (MJF/SLS)B_prototype_parts13.2x51.0x19.5
port_plate_rear_a1rigid PA12 (MJF/SLS)B_prototype_parts85.0x13.2x23.5
port_plate_rear_b1rigid PA12 (MJF/SLS)B_prototype_parts85.0x13.2x23.5
volume_bracket_upper1rigid PA12 (MJF/SLS)B_prototype_parts38.3x36.0x47.9
volume_bracket_lower1rigid PA12 (MJF/SLS)B_prototype_parts38.3x36.0x17.5
volume_roller_core1rigid PA12 (MJF/SLS)B_prototype_parts47.58x47.59x10.0
volume_roller_tyre_tpu1flexible TPUB_prototype_parts49.99x49.99x8.0
service_panel1rigid PA12 (MJF/SLS)B_prototype_parts267.4x219.72x11.0
pui_amp_carrier1rigid PA12 (MJF/SLS)B_prototype_parts83.5x68.0x6.99
hb1_carrier1rigid PA12 (MJF/SLS)B_prototype_parts79.0x49.0x8.49
pi_bracket1rigid PA12 (MJF/SLS)B_prototype_parts133.0x11.0x100.0
mic_boot_tpu_L1flexible TPUB_prototype_parts13.59x13.6x9.0
mic_boot_tpu_R1flexible TPUB_prototype_parts13.59x13.6x9.0
jack_saddle1rigid PA12 (MJF/SLS)B_prototype_parts24.0x56.5x31.5
cpn_display_corner_seat1rigid PA12 (MJF/SLS)A_fit_coupons99.5x56.0x30.04
cpn_typing_well_corner1rigid PA12 (MJF/SLS)A_fit_coupons65.5x122.0x32.23
cpn_front_right_bay_corner1rigid PA12 (MJF/SLS)A_fit_coupons77.5x59.8x33.5
cpn_carrier_corner1rigid PA12 (MJF/SLS)A_fit_coupons77.5x62.45x53.5
cpn_keybed_profile_gauge1rigid PA12 (MJF/SLS)A_fit_coupons8.0x175.67x60.73
cpn_floor_land_window1rigid PA12 (MJF/SLS)A_fit_coupons86.5x26.0x4.5
cpn_side_jack_window1rigid PA12 (MJF/SLS)A_fit_coupons11.2x80.0x36.0
cpn_grille_window_section1rigid PA12 (MJF/SLS)A_fit_coupons47.5x34.0x24.0
cpn_grille_insert_section1rigid PA12 (MJF/SLS)A_fit_coupons36.8x33.38x18.8
cpn_pad_segment_tpu1flexible TPUA_fit_coupons55.5x44.6x14.6
cpn_pad_carrier_segment1rigid PA12 (MJF/SLS)A_fit_coupons66.0x58.45x9.5
cpn_tolerance_ladder1rigid PA12 (MJF/SLS)A_fit_coupons110.0x46.0x10.0
cpn_tolerance_pegs1rigid PA12 (MJF/SLS)A_fit_coupons104.0x12.0x11.9
cpn_insert_ladder1rigid PA12 (MJF/SLS)A_fit_coupons96.0x44.0x12.0
cpn_bearing_shaft_ladder1rigid PA12 (MJF/SLS)A_fit_coupons100.0x34.0x8.0
cpn_dc_inlet_cutout1rigid PA12 (MJF/SLS)A_fit_coupons78.0x30.0x3.0
cpn_side_profile_template1cheap FDM (PLA/PETG)A_fit_coupons336.01x415.42x3.0

Not selected (files kept): shell_onepiece, shim_0p5mm, acoustic_head_section_R, acoustic_display_mock_R. The print ZIP can be assembled from docs/part-manifest.json (selected_first_build, in_assembly, stl_print, stl_assembled).

Gates

  1. G0 Process coupons (rigid PA12, flexible TPU, cheap FDM template) (OPEN)
  2. G1 HARD GATE - display (dual official sources) (OPEN - blocks shell_head)
  3. G2 Typing kit (GK64X) (OPEN)
  4. G3 LPK25 mk2 opened donor (OPEN)
  5. G4 Wheels and volume mechanism (OPEN)
  6. G5 Acoustic prototype: right side first, then BOTH sides before the full body (OPEN)
  7. G6 Audio/electronics modules (frozen audio set) (OPEN)
  8. G9 Model E side ports (new, not validated) (OPEN)
  9. G7 Bureau preflight (OPEN)
  10. G10 Production approval (not granted by this package) (OPEN - NOT APPROVED FOR PRODUCTION)
  11. G8 Structure / child load - NOT RATED (OPEN - no rating claimed)

Assembly order

  1. 0. Stage A coupons Print the selected A_fit_coupons/A_fit_and_beds files: rigid PA12 coupons in the shell bureau material, the TPU pad segment as FDM 95A (or vendor-accepted powder TPU), the side-profile template in cheap FDM. Cut 6 x 0.5 mm shims from shim stock. Close gates G0-G4, update parameters.json, rebuild.
  2. 1. Acoustic prototype (right side) Print A_acoustic_prototype; assemble chamber + driver + baffle/plenum + gaskets into the head section with the grille insert and display mock (or real monitor). Run the G5 tests before ordering the large shell.
  3. 2. Inserts Install heat-set inserts per F03-F06 (bores from the ladder): floor (cradle M3 short), port bosses, instrument-deck bosses, ledge ring (M3x3), rear-wall chamber bosses, volume-bracket side bosses (4), service rim, grille ledge bosses (M2.5 from outside), carrier crossbar and roller core (M3x3).
  4. 3. Join lower modules Dowel + bolt shell_front to shell_rear_lower at S1 (12x M4x20). Bolt both floor bars through the floor (countersunk M4x16, nylock). Slide the 6 aluminium posts into their slots from the top.
  5. 4. Music bay Prepare the wheel cradles: press 2 MR84ZZ per cradle (pockets face the wheel), place wheel + 0.4 shims in the slot, slide the 4 mm shaft from the inboard side, cross-pin the wheel, fit the 2 mm stop pin, mount the 3382H on the D-flat (the cradles are screwed down after the keybed unit, M3x10). On the bench: drill MC13 from the opened donor, screw the keybed to it, and screw the rear deck strip to the MC13 ears from below (2x M3x10 thread-forming). Fit this unit before the cradles: lower it into the bay 42 mm forward of final position and 3 mm above the lands, slide back under the typing bridge, lower onto fork shims on the lands, then 6x M3 CSK from under the floor, cut to the F14 table. Ribbon through the left bulkhead window to the controller tray (M3x20 into the tapped floor bar). Then fit the cradles and both deck wings straight down (4x M3x8 CSK). Service in reverse; qa.json service_paths sweeps these moves as solids only.
  6. 5. Side ports Drill the blank side plates to the measured jacks (left) and rocker (right). Fit the jack saddle behind the left plate on the floor bar; route jack wiring along the wall into the rear bay to HB1. Fit plates (M3x8, one M3x12 through the saddle).
  7. 6. Typing Tap the bed (6x M3), drill GK64X standoffs from the actual PCB, insert the bed diagonally under one side lip, centre, screw from below (M3x10).
  8. 7. Head Mic boots: thread the capsule wires rearward through the boot cable hole, press the capsule in through the 9 mm front lip (~11 % stretch), place the Ø9 mesh, push the boot into the roof ring. Decide spacer frame per G1; foam strip on the ledge ring; monitor in from the front (ports left); display carrier on VESA (fender washers) + 4x M3x10 into the ring. Volume: press 625ZZ into both arms, roller core + tyre on the 5 mm shaft with shims, set screw onto the flat, fit lower then upper bracket (4x M3x10), coupler, EM14 through the top plate. Chambers: ND65 rear-mounted on each baffle (M3x12 + nuts), rim gasket, 3 thread-forming screws, plenum gasket ring + side strip; screw each chamber to the rear wall from inside (M3x10 + sealing washer). Mic boots into the roof rings. Lower the head onto shell_rear_lower (dowels + 12x M4x20 at S2).
  9. 8. Grilles Grey inserts into their seats, 2x M2.5x8 CSK each.
  10. 9. Electronics Pi 4B + HiFiBerry on pi_bracket, screwed to the 4 lower REAR-WALL bosses (not the panel grid); microSD on the -X (left) short edge. PUI amp and HB1 carriers bolt to the service-panel grid. Headphone stack: 4x Keystone 25515 M3x25 on the HB1 corners, MC12 G10 plate on top, 4x M3x12 nylon posts (M3x6 from below), MIKROE-5721 resting on the posts with its jack end toward -X (25 mm plug zone), 2x 150 mm ties (<= 2.6 mm) gently over the CN1/CN2 jack housings only (never over components) through the MC12 slots, cable tails strain-relieved to the plate, D24V10F3 beside it on VHB tape. Check rear-board lift retention on the sample. Rear plates (DC inlet per cutout coupon); close the service panel (7x M3x8 CSK). Pi service order: unplug the external power adapter; disconnect the power-entry harness and remove the rear power-entry plate assembly first; unplug J4/J5/HDMI/USB; remove the service panel (7 screws; PUI and HB1 carriers come with it); remove the 4 lower bracket screws (Z 120/129); drop the bracket + Pi stack straight down through the 250 x 205 opening, rear edge Y 245.3 versus bracket back Y 241.9. The solid sweep is checked in qa.json service_paths..
  11. 10. Carrier and pad Dowels and magnets in rails/cheeks, crossbar into the carrier (3x M3x8), snap the TPU pad flange under the pocket lip.
  12. 11. Finish Feet; weigh and tip-test; add ballast only if needed (optional bays).

Metal / shaft / wood / stock cut list

idpartstocksizeqtyfeatures
MC01typing bed platealuminium 5052/6061 sheet 3.0 mm317.0 x 94.0 x 3.016 x M3 tapped (drill 2.5) at (5.5, 12.0); (5.5, 47.0); (5.5, 82.0); (311.5, 12.0); (311.5, 47.0); (311.5, 82.0) from the lower-left corner; 4 x Ø1.0 PILOT marks for GK64X standoffs at GH60 nominal (41.2, 27.6); (144.2, 46.7); (206.5, 84.9); (276.1, 27.6) - DRILL TO FIT the measured PCB only
MC02floor splice bar LEFTaluminium flat 20 x 5275.6 x 20 x 515 x Ø4.5 at [15.0, 97.62, 177.62, 247.62, 267.62] mm from the rear end (countersunk from the shell side = bar underside is plain); 2 x M3 tapped at [202.67, 264.67] for the controller tray
MC03floor splice bar RIGHTaluminium flat 20 x 5275.6 x 20 x 515 x Ø4.5 at [15.0, 97.62, 177.62, 247.62, 267.62] mm from the rear end
MC04deck posts (z=0)aluminium flat 20 x 355.4 x 20 x 32plain; deburr; ends square
MC05deck posts (z=40)aluminium flat 20 x 355.4 x 20 x 32plain
MC06rail postsaluminium flat 20 x 328.4 x 20 x 32plain
MC07carrier crossbar (NOT a seat beam)aluminium flat 20 x 3337.6 x 20 x 313 x Ø3.4 at 68.8 / 168.8 / 268.8 from the left end, centred
MC08mod-wheel shaftsground steel 4 mm h6 (silver steel)Ø4 x 17.52D-flat 2.90 across (+0/-0.03) for 3.0 mm at one end; 1.2 cross hole 7.0 mm from the plain end (wheel mid-plane); chamfer 0.3
MC09volume shaftground steel 5 mm h6Ø5 x 33.510.5 mm deep flat, 6 mm long centred 10.5 mm from the bottom end (set screw); chamfer 0.3
MC10mod wheelshardwood (maple/beech) 4 mmØ28 x 42bore 4.0 (ream to slip-fit F20); 70 deg arc slot r=9, width 2.6, 2 mm deep on the inboard face; 1.2 radial cross-pin hole
MC12headphone upper carrierunclad G10/FR4 2.0 mm, cut from AllRockets RK-5102300 300 x 300 x 2 sheet80 x 48 x 2.014 corner Ø3.4 at [(6.0, 5.0), (6.0, 43.0), (74.0, 5.0), (74.0, 43.0)] (Keystone 25515 spacers, 68 x 38); 4 post Ø3.4 at [(75.42, 13.77), (75.42, 25.77), (26.42, 12.27), (26.42, 27.27)] (drill to the Adafruit 4685 standoff sample; Ø6.5 envelope kept clear); 4 tie slots 2.8 x 1.6 (ties <= 2.6 mm over the CN1/CN2 jack housings only) at [(33.42, 5.5), (33.42, 33.9), (29.42, 5.5), (29.42, 33.9)]; origin = lower-left corner (CAD x -86.0, Y 183.9)
MC11shim stock pieces0.5 mm full-hard carbon steel Precision Brand 16978 (alt. PET/PP/stainless)18 x 18 fork, 3.8 mm slot6cut by knife/laser from step/assembled/shim_0p5mm.step outline
MC13LPK25 keybed backing bedaluminium 5052/6061 sheet 3.0 mm293.0 x 96.9 x 3.016 x M3 tapped (drill 2.5) at [(46.5, 30.9), (46.5, 76.9), (146.5, 30.9), (146.5, 76.9), (246.5, 30.9), (246.5, 76.9)] from the lower-left corner (x left to right, y rear to front); 2 side ears with Ø3.4 for the rear deck strip. DONOR HOLES NOT DEFINED: drill to the opened LPK25.

DXF/SVG: docs/drawings/ (typing bed with tapped holes + GK64X pilots, keybed backing bed, floor bars, crossbar, mod-wheel shaft, volume shaft, mod wheel, flat stock). Fasteners and inserts with counts and lengths: docs/fastener-schedule.csv.

Key numbers